Home water purifier routine maintenance and maintenance is very important

Home water purifier routine maintenance and maintenance is very important

Now many families are using water purifiers, the following Susan is here to share the daily maintenance and repair of home water purifiers and 10 brief repair methods, so that if the home water purifier has some small problems can also try to do it yourself to solve the problem.

First, the daily maintenance and maintenance

1, do not move often move may lead to internal damage to the water purifier accessories or PE pipe loose, so that the machine can not run or water leakage!
2, avoid direct sunlight regardless of what kind of water treatment machine, use should pay attention to avoid direct sunlight, because the sun will breed algae.
3, avoid heat source water purifier such as too close to the heat source, long-term baking, will affect the life of the components.
4, timely replacement of the cartridge water purifier belongs to the class of consumables, no matter what kind of material cartridge, after a period of time will be adsorbed on the work of a lot of organic matter, easy to become a breeding ground for bacteria.
5, tap water outage disposal if there is a tap water outage, after maintenance, the discharge of tap water will have rust and sediment, it is best to open the home faucet, the yellow water with sediment, rust, or used to flush the toilet, until the water is clear, and then turn on the faucet of the water purifier water.
6, less water than before after a period of time, the water purifier will be less than before, this is a normal situation, because after a period of time on the cartridge will be some attachments, more or less will affect the filter efficiency of the cartridge, but the water quality is not a problem, the flushing can alleviate this situation.
7, flushing cleaning initial flushing is mainly installed after the water purifier cartridge, piping and the entire system flushing, open the water inlet valve, water switch, wastewater switch until the water becomes clean. Regular cleaning is generally half a month or a month cleaning, mainly based on water quality, water purifier have cleaning buttons. Long-term unused flushing, generally more than three or five days without using, and again when using, open the various switch valves, drain the water for about 10 minutes, before you can use.
8, water purifier rest water purifier has been in a working condition after use, if the water purifier is not used for a long time, it is best to be able to turn off the power, turn off the water inlet ball valve, so that the water purifier rest. The ultrafiltration machine because it does not require electricity, and ultrafiltration membrane cartridge to be kept in a wet state (if the ultrafiltration membrane drying, will lead to a sharp decline in water production and can not be restored), so the ultrafiltration machine does not have to close the water inlet valve.
9, regular inspection of the water purifier is generally open after a long period of time in a working condition, in order to ensure that the water purifier better work, the regular inspection of the water purifier is indispensable. As an after-sales work, the relevant personnel will regularly test the internal parts of the water purifier one by one to see if the machine is damaged after a year of use accessories, water purification effect with the previous changes, whether the amount of water production is declining and so on.


Second, ten brief maintenance methods for water purifier

1, high-pressure pump does not start can not make water to check whether the power outage, plug is not plugged; check whether the low pressure switch is not out of order, can not be connected to the power supply; check whether the high-pressure switch or water level controller is not out of order; check the transformer, the fuse is not burned out.
2, the high-pressure pump works normally but can not make water high-pressure pump pressure loss; pre-filter clogging (pure water and wastewater or wastewater are not small); check valve clogging (wastewater, no pure water); solenoid valve failure, can not be effectively opened; RO membrane is not clogged.
3, high-pressure pump does not stop high-pressure pump pressure is insufficient to reach the set pressure; backstop valve clogging, not out of pure water (wastewater, no pure water) high-pressure switch failure, can not jump; solenoid valve malfunction, can not be effectively opened.
4, purified water and wastewater ratio is seriously out of proportion to check the flushing solenoid valve is not damaged; check the wastewater share is not blocked or too conductive; check the RO membrane is not blocked or the removal rate is seriously reduced.
5, the lack of clean water flow pre-filter blockage; lack of high-pressure pump pressure; RO membrane blockage; wastewater ratio is out of adjustment or perhaps the flushing switch is not closed.
6, the water is full of repeated machine jumping raw water pressure is lacking; check valve pressure; high-pressure switch malfunction; the system has a pressure relief phenomenon.
7, the machine constantly flushing wastewater than the failure of the flushing head may not be tight.
8, high-pressure pump shutdown but waste water constantly solenoid valve failure, can not be useful to cut off the water; View: closed pressure drum ball valve, such as still waste water, it can be concluded that the solenoid valve failure; there is a situation, close the inlet solenoid valve and then turn it over, if the machine is normal, it is determined that the water pressure is too high, the formation of the solenoid valve can not be flexible to close, it is to consider adjusting the total explication of the incoming water in order to reduce the water pressure; backstop valve pressure relief, View: closed the inlet solenoid valve, if there is still wastewater Solenoid valve, if there is still wastewater, it can be concluded that the backstop valve pressure relief.
9, pressure bucket full of water but the water can not flow out of the pressure bucket pressure relief; after the activated carbon blockage; pressure bucket ball valve is not damaged.
10, noise to see if the raw water pipeline water, the formation of booster pump idling, resulting in water machine noise; check the raw water is not normal, if the towerless water supply, is not a gas in the water; check if the booster pump is faulty, too much boom, there is a clash of voices, etc. check the water machine is not a stable place to place; check if the water pipe is too long, the pump's booming so that the pipe knocking the casing to check if the hot water is not hot water to form the noise! Too large; check the compressor is not normal.
 If you have any other solutions or if you need any water purifiers ,pls feel free to contact us!